![]() ![]() The reason for my reluctance was that one of the guidelines for OpenVPN, going back to it's peer-to-peer days, is that the server should not be able to do anything to the client that the client doesn't explicitly allow. The drawback is that you are allowing the changes : ) Please reply if this modified file fixes the problem.Īllow-override-of-manually-set-dns-up.sh.zip ![]() (Note: other manually-set entries such as the domain will still not be changed you'd have to make similar changes to the script for each such entry.) The only changes to the standard script are that lines 330-333 and line 358 are commented out so manually entered DNS entries are ignored. zip, rename the script to "up.sh" before adding it to your configuration. zip of such a modified version of Tunnelblick's standard "up" script that allows changing manually-entered DNS entries. (Install by dragging/dropping the copy onto the Tunnelblick icon in the menu/status bar.)Īttached is a. Let Tunnelblick manage configurations: change a copy of the configuration and then install that changed configuration. Important: Tunnelblick VPN Configurations can be located in different places (depending on whether they are shared or private), so ~/Library/Application Support/Tunnelblick/Configurations/.tblk/Contents/Resources is not always the correct place for them. Remember to remove your pre-connect.sh and post-disconnect.sh scripts. Put the modified script in your Tunnelblick VPN Configuration as a file named "up.sh" so it will be used instead of the standard script. Until such changes are made to Tunnelblick, your best bet would be to use a copy of Tunnelblick's standard up script modified so that the change is allowed. ![]() It was a deliberate decision, but perhaps it is time to allow such modifications. Tunnelblick has refused to modify manually-entered network settings for many years. We monitor access to the Tunnelblick website from 15 networks distributed around the world, so the most likely explanation is a problem with your Internet connection.Ĭan you reach the Tunnelblick website in a browser?Ĭan you reach the "IP checking" page? (The response should be en empty page that just shows something like ,637xx, (where each of the "x"s is a digit).Ĭan you connect your VPN (ignoring the warning) and then reach those two pages? If so, that would tend to support the idea that it is a problem with your Internet access.I read somewhere I need to write 2 scripts.Īs you saw, this won't work. Our monitoring shows the website itself is OK. The only other thing that can cause this is a problem between your computer and the Tunnelblick website. The Tunnelblick program and Tunnelblick website are working and have been working fine. That isn't necessarily a problem because for some uses of a VPN you don't want the IP address to change. It does that by accessing the Tunnelblick website before you connect, and then again after you connect each time the Tunnelblick website returns your IP address, so Tunnelblick can warn you if the IP address didn't change. It just means that Tunnelblick was not able to test whether your IP address changed. This warning, if not accompanied by other warnings, does not mean that you haven't connected to the VPN properly. This is presumably due to network congestion or other transitory problems. In our experience, this problem happens randomly about 0.1% of the time - that is, about 1 time per thousand attempts. 13:35:06.307289 Tunnelblick An error occured fetching IP address information before connecting 13:40:08.488017 Tunnelblick Set 'expect disconnect 1 -SLibrary-SApplication Support-STunnelblick-SUsers-Si347131-Swazh-Dtblk-SContents-SResources' 13:40:17.552997 Tunnelblick Cleared 'expect disconnect 0 -SLibrary-SApplication Support-STunnelblick-SUsers-Si347131-Swazh-Dtblk-SContents-SResources' 13:40:52.169760 Tunnelblick currentIPInfo(Name): IP address info could not be fetched within 34.3 seconds the error was 'Error Domain=NSURLErrorDomain Code=-1001 "The request timed out." UserInfo=' the response was Thanks for the Console Log listings and other info. by the way, we all use MAC.įollowings are part of the logs. ![]() Some colleges meet this issue only sometimes. Hi happens to me every time when i connect( that means i haven't connected success once yet),some of my colleges also meet the same problem. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |